|
PTEAZER™
PARTS AND ACCESSORIES
PART # PZR172U
IMPORTANT:
Be sure to test fit all parts to the vehicle before painting as
PTEAZER™
will not be responsible for the painting on a defective part that
must be returned.
PTEAZER™
"PTEAZER ILLUSION REAR BUMPER
WITH STEEL REINFORCEMENT
INSTALLATION INSTRUCTIONS PART # PZR172U
TOOLS REQUIRED
FOR INSTALLATION:
7mm Socket
10mm Tube Socket
13mm Socket
1/8 Drill
Phillips and flat head screw drivers
NOTE:
Urethane parts should not subjected to baking ovens as they may
warp or lose their original shape.
Urethane parts should be air dried only. BAKING OVENS WILL VOID
ALL WARRANTIES.
TEST FIT ALL PARTS BEFORE PAINTING.
STEPS:
1. Remove original muffler and tail pipe. (Do not attempt to drive
with original muffler - The heat of the muffler will damage the
new Illusion Bumper.
2. DISCONNECT ORIGINAL BACKUP LIGHTS. If necessary disconnect
the wiring harness clips from the reinforcement bar.
3. OPEN REAR LIFT GATE
4. REMOVE PLASTIC SCUFF PANEL to access bumper bolts.
5. REMOVE PLASTIC GROMETS to access bumper bolts.
6. REMOVE ORIGINAL BUMPER COVER. Save original nuts to use with
new rollpan.
7. TEST FIT before proceeding to painting instructions - page
2.
IMPORTANT--Minor adjustments may be required prior to primer and
paint.
8. Attach factory back-up lights using supplied screws and guide
holes.
NOTE: Remember to plug in the license plate lamp before mounting
the bumper.
9. Two people need to hold the new bumper in place to avoid scratching
the vehicle. Use original hardware from the old bumper to reattach
the PTeazer Illusion rear bumper
10. Drill holes for fender liner screws and attach fender liner.
11. For additional security, MOUNT THE ANGLE BRACKET from the
flanges on the bumper up to the rear floor brace using the lowering
bracket on the drivers side.
IMPORTANT
INFORMATION:
PTEAZER INC. warrants all parts 100% prior to painting or installation.
Please report any shipping or other damage immediately upon opening
of package. All damages must be reported within 5 days of receipt.
Toll-Free Tel: 877-783-2937
PTEAZER®
parts and accessories are protected by trademark, copyright and
patent. Any attempt to reproduce, or otherwise copy any part or
accessory will be aggressively prosecuted to the fullest extent
of the law.
URETHANE
PARTS PREPARATION, PAINTING INSTRUCTION
IMPORTANT:
Be sure to test fit all parts to the vehicle before painting as
PTEAZER® will not be responsible for the painting on a defective
part that must be returned.
- SAND
edges as necessary.
- WASH
paintable surfaces with 3M #7447 Scotchbrite pad, TSP and warm
water.
- SAND
the paintable surfaces with 320 wet or dry - at this point the
surface should appear to be a dull medium gray and scratched
surface.
- CLEAN
paintable surfaces with either Dupont 2319S or Sherwin Williams
#R7K157 pr R7K158 or equivalent.
- FILL
any slight surface imperfections, if applicable, with "Evercoat"
glazing putty and sand smooth.
- APPLY
Dupont #2322 or Sherwin Williams P6C61 adhesion promoter or
equivalent.
- APPLY
Basecoat/clear coat following the paint manufacturer's recommendations
for painting flexible polyurethane plastic.
Note: Some painters prefer, after cleaning the surface, to apply
Dupont "Variprime" (or equivalent), let dry and scuff
with a Scotchbrite pad and then apply basecoat/clear coat.
Note:
Painting of grille is not to exceed temperature of 90°F as
grille may lose shape. TEST FIT ALL PARTS BEFORE PAINTING.
For technical
assistance, please call our toll-free telephone number 877-783-2937.
IMPORTANT
INFORMATION:
PTEAZER INC. warrants all parts 100% prior to painting or installation.
Please report any shipping or other damage immediately upon opening
of package. All damages must be reported within 5 days of receipt.
Toll-Free Tel: 877-783-2937
PTEAZER™
parts and accessories are protected by trademark, copyright and
patent. Any attempt to reproduce, or otherwise copy any part or
accessory will be aggressively prosecuted to the fullest extent
of the law.
|
