|
PTEAZER™ RETRO FULL GRILLE/BUMPERETTE FRONT FASCIA (2-PC)
WITH STEEL REINFORCEMENT
INSTALLATION INSTRUCTIONS PART # PZG128U/PZF117U SERIES 042302
IMPORTANT:
Be sure to test fit all parts to the vehicle before painting as
PTEAZER™
will not be responsible for the painting on a defective part that
must be returned.
STEPS:
1. REMOVE FACTORY GRILLE: Using a 7mm Socket, remove the four
screws at the top of the grille, then push grille down from top
and at the same time pull forward. (Do not discard the screws,
you will need them when reinstalling the PTeazer grille.)
2. Using 7mm Socket remove the three screws on splashguard and
edge of factory bumper. Repeat on both sides. Remove three screws
on bottom of the scuff strip where fastened to lower radiator
support panel. Also remove the two screws at grille opening (where
grille mounts).
3. On both sides of the factory bumper, where it meets the fenders,
remove two 10mm nuts using a 10mm tube socket.
4. Pull splash guard back, reach in and DISCONNECT FOG LIGHTS.
On left side by fog lamp, remove speed clip on splashguard.
5. Bumper cover is now ready to be removed.
6. REMOVE ORIGINAL REINFORCEMENT: Use 13mm Socket to remove bolts.
(Save bolts for installing the PTeazer reinforcement.)
7. Remove all hardware from stock bumper and place in same place
on new PTeazer Front Fascia. DON'T FORGET TO PLACE FOG LAMPS IN
PTEAZER FASCIA BEFORE FITTING TO CAR.
8. Before fitting PTeazer Fascia, BOLT YOUR PTEAZER REINFORCEMENT
IN PLACE using the bolts from the stock reinforcement.
9. Using the original bumper cover lower fasteners, ATTACH SCUFF
STRIP to PTeazer Fascia. (OPTIONAL)
10. You are now ready to fit your PTeazer Fascia using exactly
the same screws from your stock bumper.
INSTALL PTEAZER FRONT FASCIA to existing factory bumper cover
mounting locations. (This may require two people to ensure correct
installation. Minor adjustments may be necessary.)
NOTE: Some fascias may need cut outs in the plastic scuff-strip
to clear the two outermost bolt heads located on the bottom of
the radiator support. Try fitting part first before making cuts.
NOTE: In some cases, due to factory assembly variations, headlamps
may need to be adjusted down slightly if there is a gap between
the fascia and lamps.
11. When
satisfied with fit, REMOVE fascia and scuff-strip. (Remember to
test fit fog lights prior to final paint, as some adjustment may
be needed).
12. Follow PAINT Instructions below. Reinstall fog lights and
spoiler.
13. REINSTALL Fascia. Connect fog lights.
14. Once the fascia is fitted you can now slip your new PTEAZER
GRILLE in place. This grille will locate at the bottom of the
fascia and at the same points as the stock grille.
15. URETHANE PARTS PREPARATION, PAINTING INSTRUCTION
IMPORTANT:
Be sure to test fit all parts to the vehicle before painting as
PTEAZER will not be responsible for the painting on a defective
part that must be returned.
·
SAND edges as necessary.
· WASH paintable surfaces with 3M #7447 Scotchbrite pad,
TSP and warm water.
· SAND the paintable surfaces with 320 wet or dry - at
this point the surface should appear to be a dull medium gray
and scratched surface.
· CLEAN paintable surfaces with either Dupont 2319S or
Sherwin Williams #R7K157 pr R7K158 or equivalent.
· FILL any slight surface imperfections, if applicable,
with "Evercoat" glazing putty and sand smooth.
· APPLY Dupont #2322 or Sherwin Williams P6C61 adhesion
promoter or equivalent.
· APPLY Basecoat/clear coat following the paint manufacturer's
recommendations for painting flexible polyurethane plastic.
Note: Some
painters prefer, after cleaning the surface, to apply Dupont "Variprime"
(or equivalent), let dry and scuff with a Scotchbrite pad and
then apply basecoat/clear coat.
IMPORTANT:
Painting of grille is not to exceed temperature of 90°F. Grill
will loose shape if exposed to heat in baking oven. PTeazer will
not be held responsible for any damage as the result of heat exposure.
TEST FIT ALL PARTS BEFORE PAINTING.
| Install
Instructions Video |
|
Broadband
DSL/Cable |
56k
Dial Up |
| |
|
For technical
assistance, please call our toll-free telephone number 877-783-2937.
IMPORTANT
INFORMATION:
PTEAZER INC. warrants all parts 100% prior to painting or installation.
Please report any shipping or other damage immediately upon opening
of package. All damages must be reported within 5 days of receipt.
Toll-Free Tel: 877-783-2937
PTEAZER™
parts and accessories are protected by trademark, copyright and
patent. Any attempt to reproduce, or otherwise copy any part or
accessory will be aggressively prosecuted to the fullest extent
of the law.
Back
to Technical Information
|
